Peugeot Boxer 2022+ MagSafe phone mount fitment reference — Tactic Engineering, Swiss made

iPhone on the Tactic MagSafe phone mount in the centre cup holder of a pre-2022 Fiat Ducato, same dashboard as Ram ProMaster

Qi2 MagSafe charger on the Tactic phone mount, Fiat Ducato / Ram ProMaster dashboard cup holder

Phone mount installed in the centre cup holder of a Fiat Ducato, Citroën Jumper, Peugeot Boxer or Ram ProMaster

Fitment check: the cup holder this mount fits, with the step in the middle and the TX25 Torx screw at the bottom

Installation in four steps: remove the TX25 Torx screw in the Fiat Ducato pre-2022 cup holder, seat the mount, refit the screw, place the phone. Same for Citroën Jumper, Peugeot Boxer and Ram ProMaster

Peugeot Boxer pre-2022 Phone Mount

CHF 89.00

Taxes included. Shipping calculated at checkout.

Driving Side LHD

LHD

Mount Type

MagSafe-compatible (charger included)

In stock, ready to ship.Order before 11:00 CET: ships in 2 working days. Otherwise 3.

★ 4.9 · 276 store reviewsShips from 🇨🇭 SwitzerlandSwiss VAT included2-year warranty

✓Complete your kit · save up to 15%

Trusted by the industry

Peugeot Boxer pre-2022 Phone Mount

Built for the Peugeot Boxer dashboard. Sits in the centre cup holder. One TX25 Torx screw. No drilling. No adhesive.

Made in SwitzerlandPeugeot BoxerCentre cup holderLeft-hand driveQi2 charger included (MagSafe)

Check your cup holder first.

This mount is made for one cup holder: the round one in the centre of the dashboard, with the step through the middle and a Torx screw at the bottom. Compare yours with the cup holder photo in the gallery before ordering.

Same as the photo

This mount

Round cup holder, step in the middle, TX25 Torx screw at the bottom. You are on the right page.

Different cup holder

The other version

Your Boxer needs the Peugeot Boxer 2022+ Phone Mount. Not sure? Send us a photo of your cup holder and we will tell you which one fits.

One screw. Done.

Remove the TX25 Torx screw at the bottom of the cup holder and fit the mount in its place. Plug the charger into a USB-C source. Snap the phone on, drive.

Nothing is cut, drilled or glued. Take the mount out and the cup holder is back to factory.

Four badges. One dashboard.

In this generation the Peugeot Boxer, Fiat Ducato, Citroën Jumper / Relay and Ram ProMaster leave the same factory with the same dashboard. Same centre cup holder, same TX25 screw, same mount. Motorhomes and campers built on the Boxer keep the factory dashboard, so the mount fits them too.

Fitment. Read this before ordering.

Fits, with the cup holder shown in the photo

Peugeot Boxer, pre-2022 Fiat Ducato, pre-2022 Citroën Jumper / Relay, pre-2022 Ram ProMaster 1500 / 2500 / 3500 Opel / Vauxhall Movano on the Ducato platform, if the cup holder matches Motorhomes and campers on these chassis with the original cup holder

Does not fit

A different cup holder. See the Boxer 2022+ version. Right-hand drive (UK, Ireland, Australia). Not available yet.

Cup holder does not match?

Peugeot Boxer 2022+ Phone Mount.

Built for the van

Fit

Made for the cup holder

Shaped to the centre cup holder. Sits low, out of the way of the radio and the vents.

Install

No drilling, no adhesive

One factory Torx screw. Reversible. Relevant at resale and on fleet vans.

Hold

Magnetic Qi2 alignment

The phone stays put on cobbles, gravel and speed bumps. You pull it off. It does not fall off.

Origin

Designed and made in Switzerland

Sintered nylon, manufactured in-house. 2-year warranty in Switzerland and the EU, 1 year elsewhere. Every part replaceable at fair prices.

Specifications

VehiclePeugeot Boxer, pre-2022. Left-hand drive.

PositionCentre dashboard cup holder

InstallRemove one TX25 Torx screw, fit the mount. Reversible.

Tools requiredTX25 Torx driver

Charger standardQi2 wireless, up to 25 W

Power inputUSB-C PD, 30 W or stronger source for full speed

MagnetMagnetic Qi2 alignment

Max case thickness3 mm (any MagSafe-compatible case)

Phone compatibilityiPhone 12+, any Qi2 Android or MagSafe-compatible case

MaterialSintered nylon, vehicle-specific profile

OriginDesigned and manufactured in Switzerland

MagSafe® and iPhone® are trademarks of Apple Inc. Peugeot®, Fiat®, Citroën®, Opel®, Vauxhall®, Ram® and ProMaster® are trademarks of their respective owners. Tactic Engineering is an independent manufacturer and is not affiliated with, endorsed by, or sponsored by any of the above companies.

04 — HOW IT IS MADE

It starts as a 3D scan of your car.

Then hours and hours of modelling. Then nylon powder, fused by a laser one layer at a time, until the powder holds the shape of your console.

Parts coming out of the powder bed. Cleaned and polished in-house.

The rubber is the whole point.

This mount is designed with rubber around it. That rubber is what locks it in place — and what keeps it from ever marking the interior. Nothing scratches. Nothing presses into leather or Alcantara.

It is also why it goes in and comes out in seconds. No tape to peel off and no residue left behind. No suction cup to let go in the heat. No tools, no screws, nothing driven into dashboard plastics that were never made to take it.

We do the hours so the install takes seconds.

Scanning, modelling, printing, finishing and assembly happen in one building in Ticino, Switzerland. Nothing arrives finished. Nothing is rebadged. When a part needs to change, it changes that week.

swiss made

the original