Buy it with — Carry skis, boards, or kites. Magnetic, no roof rack needed.
Toyota Land Cruiser 250 2024+ Phone Mount
Details that make the difference
Look at the black rubber strip.
There are many phone mounts out there. Nobody else uses it.
- Quiet. The rubber absorbs vibration, so the mount adds no rattle or noise while you drive.
- Stays put. The rubber is thicker than the slot, so the mount is hard to pull out, even without adhesive tape.
- No scratches. No plastic rubbing on plastic, so your interior stays as it left the factory.
Typical hobby 3D-printed mounts do not have it.
Ball joint
Knurled grip
Tilt the phone within its range to the angle you like.
The knurled nut gives more grip when you tighten it to lock the position.
Trusted by the industry
Toyota Land Cruiser 250 2024+ MagSafe Phone Mount
Phone mount for the Toyota Land Cruiser 250 (2024+). Pushes into the front centre console cupholder in 5 seconds. Qi2 MagSafe charger up to 15 W included. No drilling, no adhesive, no tools.
At a glance
Use it for
Keep your phone in view in the Land Cruiser 250, charging over Qi2 MagSafe up to 15 W, with a ball joint and knurled grip to set the angle.
What it fits
Toyota Land Cruiser 250 (2024+). Pushes into the front centre console cupholder in 5 seconds, no tools, no drilling, no adhesive.
Shipping
Leaves our Swiss workshop within 48 working hours. Free shipping from CHF 150, £150, €250 or $279.
MagSafe.
MagSafe
A complete kit. Mount plus a Qi2 wireless charger, up to 15 W. Push it into the front center console cupholder and drive.
Built for your Land Cruiser.
Made for your Land Cruiser
A center console cupholder mount designed specifically for the Toyota Land Cruiser 250.
Designed in Switzerland
Industrial SLS 3D printing. Made in Switzerland.
No drilling, no adhesive
No suction cups. No adhesive. No drilling. No tools.
Built for off-road
Industrial SLS nylon survives vibration, temperature extremes, and sustained abuse.
How it works.
The holder sits in the front cupholder of the center console, the one closer to the dashboard. We chose this position deliberately. It puts your phone at a natural viewing angle while keeping the rear cupholder completely free for your bottle or cup.
The TPU ring creates a friction lock. Preventing scratches, eliminating rattles, keeping everything secure.
The included Qi2 charger snaps into the mount. Your phone magnetically attaches. It stays put over corrugations, rock steps, and everything in between.
Installation takes 5 seconds. No tools required.
Why the front cupholder?
The LC 250 has two cupholders in the center console. We tested both. The front position gives you a natural, comfortable viewing angle for navigation without blocking your line of sight. More importantly, it keeps the rear cupholder completely accessible, so your drink stays within easy reach.
Using the rear cupholder would mean an awkward phone angle and your bottle trapped behind the mount. We tried it. It's not the right call.
Fitment.
- Toyota Land Cruiser 250 (2024+).
- Fits the front center console cupholder.
Specifications.
MagSafe® and iPhone® are trademarks of Apple Inc. Quad Lock® is a trademark of Annex Products Pty Ltd. Peak Design® is a trademark of Peak Design Ltd. RAM Mounts® and X-Grip® are trademarks of National Products Inc. Tactic Engineering is an independent manufacturer and is not affiliated with, endorsed by, or sponsored by any of the above companies.
Compatibility at a glance
| Vehicle or phone | Works | Notes |
|---|---|---|
| Toyota Land Cruiser 250 (2024+) | Yes | Front centre console cupholder, the one closer to the dashboard. |
| Rear cupholder | Not recommended | Awkward phone angle, and your bottle is trapped behind the mount. |
| iPhone 12 to 17, all Qi2 devices, AirPods | Yes | Qi2 charger included, up to 15 W. |
| MagSafe or Qi2 magnetic cases | Yes | Charges through the case. |
The rear cupholder stays free for your bottle or cup.
FAQ
Which cupholder does it use?
The front one in the centre console, closer to the dashboard. It gives a natural viewing angle for navigation and keeps the rear cupholder free.
Is a charger included?
Yes. A Qi2 wireless charger, up to 15 W, with a braided USB-C cable. Use any USB-C PD charger, 30 W or stronger for full speed.
Will it rattle or scratch the interior?
No. The TPU cushion ring creates a friction lock that prevents scratches and eliminates rattles.
How long does installation take?
5 seconds. Push it into the cupholder. No tools, no drilling, no adhesive.
Will it hold off-road?
Your phone attaches magnetically and stays put over corrugations and rock steps. Industrial SLS nylon, made in Switzerland.
Quick questions
Which phones work?
iPhone 12 and newer and all Qi2 devices, also through MagSafe and Qi2 magnetic cases.
Pairs well with
It starts as a 3D scan of your car.
Then hours and hours of modelling. Then nylon powder, fused by a laser one layer at a time, until the powder holds the shape of your console.
The rubber is the whole point.
This mount is designed with rubber around it. That rubber is what locks it in place — and what keeps it from ever marking the interior. Nothing scratches. Nothing presses into leather or Alcantara.
It is also why it goes in and comes out in seconds. No tape to peel off and no residue left behind. No suction cup to let go in the heat. No tools, no screws, nothing driven into dashboard plastics that were never made to take it.
We do the hours so the install takes seconds.
Scanning, modelling, printing, finishing and assembly happen in one building in Ticino, Switzerland. Nothing arrives finished. Nothing is rebadged. When a part needs to change, it changes that week.
swiss made
the original
Toyota Land Cruiser 250 2024+ Phone Mount
LHD / MagSafe-compatible (charger included)