Home/Field Notes/Range Rover Velar Phone Mount Guide
Best Range Rover Velar Phone Mount in 2026: Buyer Guide
The Velar was drawn to look clean: touchscreens, slim vents, smooth surfaces. That is exactly why phone mounts look wrong in it. There is nothing to clip onto and nowhere you want glue. The console has a square storage pocket, and that is where ours goes.
Made for this car
Range Rover Velar Phone MountSlots into the square console pocket. Qi2 charger included. No drilling, no adhesive.
View the Velar mount →Spec sheet
01Why the usual mounts fail in a Velar
Vent clips do not grip the slim Velar vents well and block the air. Adhesive pads on leather or soft-touch surfaces leave a mark for good. Suction cups put the phone high in the windscreen, in your view of the road, and fall off in the heat.
And anything placed in front of the touchscreens covers the controls the Velar relies on. Climate, seats, drive modes: they live on glass.
| Option | Where the phone sits | Rough roads | Charging | Marks left |
|---|---|---|---|---|
| Suction cup on the windscreen | High on the glass, out of reach | Lets go in heat and cold | Separate cable | Ring on the glass |
| Vent clip | In front of a vent, blocks the air | Sags and rattles | Separate cable | Can crack a louvre |
| Adhesive dash pad | Wherever the dash is flat enough | Holds until the sun softens the glue | Separate cable | Residue and marks |
| Tactic, vehicle-specific | In the square console pocket, by the gear selector | Anchored in the console. No wobble | Qi2 up to 15 W, built in | None. Reversible |
02Where ours goes
In the square storage pocket in the centre console. The base is shaped to the pocket and slots in. No tools, no screws, no tape. Lift it out and the pocket is as it was.
The phone ends up low, by the gear selector, clear of the screens. A ball joint lets you tilt it toward the driver, and the knurled nut locks the angle.
03What you get
The vehicle-specific base with a MagSafe-compatible Qi2 wireless charger. Up to 15 W over USB-C. Magnetic alignment holds the phone on the charger. A rubber strip on the base takes up vibration and stops plastic rubbing on plastic.
Scanned from the car
The base is modelled on a 3D scan of the interior. It is shaped to one recess in one car.
Sintered nylon
SLS printed in our own workshop. Stiff, light, does not soften in a hot car.
Qi2, up to 15 W
Magnetic alignment holds the phone and charges it. USB-C input.
Made in Switzerland
Designed and manufactured in-house. Two-year warranty. Spare parts for every piece.
04Install
-
01Open and empty the square pocket in the centre console.
-
02Slot the base in.
-
03Plug the Qi2 charger into a USB-C source. A 30 W USB-C PD charger gives full speed.
-
04Set the angle with the ball joint, tighten the knurled nut, snap the phone on.
That is the whole install, as the video above shows.
05Fitment
- Range Rover Velar with the square console pocket shown in the photos and video
- Left- and right-hand drive
- Velar without that pocket
- Range Rover Evoque, Sport and full-size models (different consoles)
The mount needs the square pocket in the console. Compare yours with the product photos, or send a photo to team@tacticengineering.com and we tell you.
Driving a full-size L405? See the Range Rover L405 phone mount.
The Original. Built in Switzerland since 2020.
Keep the Velar clean. Keep the phone in view.
Swiss made. No drilling. Qi2 up to 15 W.
Frequently asked questions
Which Velar does it fit?
Any Velar with the square storage pocket in the centre console shown in the photos and video, left- or right-hand drive. Send us a photo if your console looks different.
Will it rattle or scratch the console?
No. A rubber strip on the base absorbs vibration and holds it in place without tape.
Does it cover the touchscreens?
No. The phone sits low in the console, by the gear selector.
Which phones work?
iPhone 12 and newer, any Qi2 Android phone, or any phone in a MagSafe-compatible case. Case thickness up to 3 mm.
Where does the power come from?
The Qi2 charger runs on USB-C. A USB-C PD source of 30 W or more gives full speed, for example our 30W Mini USB-C Car Charger.
Does it need drilling or glue?
No. No drilling, no adhesive, no screws. Take it out and the interior is as it left the factory.
What if a part breaks?
Two-year warranty in every country. Every part is made in-house and sold separately, so you replace a part, not the mount.
When does it ship?
Orders leave our workshop in Switzerland every Tuesday and Friday.
MagSafe and iPhone are trademarks of Apple Inc. Range Rover, Land Rover and Velar are trademarks of Jaguar Land Rover Limited. Vehicle names are used to describe fitment only. Tactic Engineering is an independent manufacturer and is not affiliated with, endorsed by, or sponsored by any of the above companies.
