Home/Field Notes/Range Rover L405 Phone Mount Guide
Best Range Rover L405 (2013-2021) Phone Mount in 2026: Buyer Guide
The L405 cabin is wood, leather and metal. Nothing in it was drawn for a phone, and nothing in it should be glued, clipped or drilled. We scanned the centre console and made a mount that sits between the cup holders, next to the rotary gear selector. It charges over Qi2, and it comes out without a trace.
Made for this car
Range Rover L405 Phone Mount (2013–2021)Sits between the cup holders. Qi2 charger included. No drilling, no adhesive.
View the L405 mount →Spec sheet
01Why the usual mounts are wrong for an L405
Adhesive on leather is permanent. A pad on the dash or the console takes the grain with it when it comes off. On a car like this, that is a repair bill.
Vent clips block the air and mark the vanes. The L405 vents are part of the design. A clip hanging a phone off them sags over time and leaves marks.
Suction cups put the phone in the windscreen. High, far, and in your view of the road. In summer they let go.
The L405 also has a large touchscreen in the centre stack. Anything mounted in front of it covers the controls you use most.
| Option | Where the phone sits | Rough roads | Charging | Marks left |
|---|---|---|---|---|
| Suction cup on the windscreen | High on the glass, out of reach | Lets go in heat and cold | Separate cable | Ring on the glass |
| Vent clip | In front of a vent, blocks the air | Sags and rattles | Separate cable | Can crack a louvre |
| Adhesive dash pad | Wherever the dash is flat enough | Holds until the sun softens the glue | Separate cable | Residue and marks |
| Tactic, vehicle-specific | Between the cup holders, low in the console | Anchored in the console. No wobble | Qi2 up to 15 W, built in | None. Reversible |
02Where ours goes
Between the two cup holders in the centre console. The base is modelled on a 3D scan of the L405 console and sits there by shape alone. No screws, no tape, nothing pressed into the wood or the leather.
The phone ends up low and at hand, next to the rotary gear selector. The touchscreen, the climate controls and the vents stay free. Glance down for the next turn, reach over to answer a call.
03What you get
The kit is the vehicle-specific base with a MagSafe-compatible Qi2 wireless charger on top. Up to 15 W over USB-C. Magnetic alignment centres the phone on the coil and holds it there through corners and on rough tracks. Tilt the charger to set the viewing angle.
Scanned from the car
The base is modelled on a 3D scan of the interior. It is shaped to one recess in one car.
Sintered nylon
SLS printed in our own workshop. Stiff, light, does not soften in a hot car.
Qi2, up to 15 W
Magnetic alignment holds the phone and charges it. USB-C input.
Made in Switzerland
Designed and manufactured in-house. Two-year warranty. Spare parts for every piece.
04Install
-
01Slide back the cup holder cover and set the base between the two cup holders. It drops into place.
-
02Plug the Qi2 charger into a USB-C source. A 30 W USB-C PD charger gives full speed.
-
03Tilt the charger to the angle you want.
-
04Snap the phone on.
That is the whole install, as the video above shows. Lift it out and the console is as Land Rover built it.
05Fitment
- Range Rover L405, 2013–2021, with the console shown in the photos and video
- Range Rover L322, 2002–2012
- Range Rover L460, 2022+
- Range Rover Sport (different console)
- Right-hand drive. Not available yet
Driving a Velar? We make a Range Rover Velar phone mount too.
The Original. Built in Switzerland since 2020.
A place for the phone. Nothing glued to the leather.
Swiss made. No drilling. Qi2 up to 15 W.
Frequently asked questions
Where exactly does it sit?
In the centre console, between the two cup holders, next to the rotary gear selector. The video in this guide shows the exact spot.
Does it fit the Range Rover Sport?
No. The Sport has a different console. This mount is for the full-size L405.
Does it fit the L405 SVAutobiography or the long wheelbase?
If your console matches the photos on the product page, it fits. Send us a photo if you are unsure.
Which phones work?
iPhone 12 and newer, any Qi2 Android phone, or any phone in a MagSafe-compatible case. Case thickness up to 3 mm.
Where does the power come from?
The Qi2 charger runs on USB-C. A USB-C PD source of 30 W or more gives full speed, for example our 30W Mini USB-C Car Charger.
Does it need drilling or glue?
No. No drilling, no adhesive, no screws. Take it out and the interior is as it left the factory.
What if a part breaks?
Two-year warranty in every country. Every part is made in-house and sold separately, so you replace a part, not the mount.
When does it ship?
Orders leave our workshop in Switzerland every Tuesday and Friday.
MagSafe and iPhone are trademarks of Apple Inc. Range Rover, Land Rover and Velar are trademarks of Jaguar Land Rover Limited. Vehicle names are used to describe fitment only. Tactic Engineering is an independent manufacturer and is not affiliated with, endorsed by, or sponsored by any of the above companies.
