Magnetic Supports — Starlink Mini
Buy it with — Add the magnetic RotoPax plate for fuel, water, and gear.
Trusted by the industry
Magnetic Supports — Starlink Mini
Four magnets under the Starlink Mini. The dish drops onto a steel roof and stays put. No rack, no drilling, no adhesive.
Use it for: Put a Starlink Mini on the steel roof of your vehicle and keep it there, with no rack, no drilling and no adhesive.
What it fits: Starlink Mini only, on steel-bodied vehicles. 4 supports, one rubber-coated 56 kg magnet each, heat-resistant to 175°C. Not for Gen.2, Gen.3 or aluminium bodies (Land Rover, new Ford Bronco).
Shipping: Ships within 48 h. Free shipping from CHF150, £150, €250 or $299.
Three ways to hold a Mini on a roof.
Tactic Engineering designed the first magnetic mounts for camper vans, in December 2021. Every part is designed and manufactured in Switzerland. Here is how this mount compares to what else you can buy.
Drilled bracket
Decades-old generic hardware, often made in Asia. You drill the roof, and the holes are permanent.
Magnetic look-alike
A recent copy of our design, often made in Asia. Pull force is usually left unspecified.
Tactic magnet
Our design, December 2021. Four magnets, 56 kg pull each, tested. Thousands of vans worldwide since 2021.
Nothing to modify
No drilling required. The supports come off as fast as they go on, and the roof stays as it left the factory.
Fits the Mini. Only the Mini.
These supports are cut for the Starlink Mini. The Gen.2 and Gen.3 dishes are different shapes and take different mounts.
Fits
Does not fit
Gen.2 antenna, parked: Magnetic Stand — Starlink Gen.2. Gen.2 on curved or non-flat surfaces: Magnetic Mounts — Starlink Gen.2 (Curved Surfaces). Gen.3 antenna: Magnetic Supports — Starlink Gen.3.
Select your make and model in the compatibility tool.
What you get
Four magnetic supports
One rubber-coated magnet per support, 56 kg pull force each, holding the Mini at four points.
Stainless steel throughout
Threads and nuts in stainless steel. No rust, even after years of outdoor exposure.
Holds to 175°C
Heat-resistant plastic, rated to 175°C / 347°F.
No drilling, no rack
The supports magnet onto the roof in seconds and lift off in seconds.
Specifications
The original. Invented here.
Tactic Engineering invented magnetic van accessories. Every product is designed, produced and hand-assembled in Switzerland. If you have seen similar products elsewhere, they are copies of ours.
Also available through our official distributors
Shipping, duties and warranty
Legal disclaimer: According to the Swiss regulatory authority, the magnetic supports are classified under cargo securing equipment, for which the driver assumes responsibility. Tactic Engineering cannot be held accountable for any incidents resulting from the use of our products. It is the user's responsibility to ensure compliance with local regulations and laws regarding cargo securing. Please use the magnetic supports responsibly and exercise caution.
Starlink® is a trademark of Space Exploration Technologies Corp. Tactic Engineering is an independent manufacturer and is not affiliated with, endorsed by, or sponsored by Space Exploration Technologies Corp.
Compatibility at a glance
| Vehicle or item | Fit |
|---|---|
| Starlink Mini | Yes |
| Starlink Gen.2 or Gen.3 | No, different mounts |
| Steel-bodied vehicles | Yes |
| Aluminium bodies (Land Rover, new Ford Bronco) | No |
FAQ
Does it fit my dish?
These supports are cut for the Starlink Mini only. The Gen.2 and Gen.3 dishes are different shapes and take their own mounts.
What is in the box?
Four magnetic supports, each with one rubber-coated 56 kg magnet, stainless steel threads and nuts, and heat-resistant plastic rated to 175 °C.
Will it hold on my vehicle?
The magnet needs steel underneath. It holds on steel panels and does not hold on aluminium. Not sure? Put a fridge magnet on the spot first: if it sticks firmly, the mount holds.
How fast does it ship, and is shipping free?
Orders leave our Swiss facility within 48 working hours. Shipping is free from CHF 150 in Switzerland and £150 in the UK, and from €250 in the EU and $299 in the US.
Quick questions
Do I need to modify the roof?
No. No drilling is required, and the supports come off as fast as they go on.
Pairs well with
swiss made
the original
