Buy it with — Add the magnetic towel hook for your shower setup.
Magnetic Shower Mount
Trusted by the industry
Magnetic Shower Mount
Your shower head, held on the side of the van. The magnet grips the steel body panel. No drilling, no suction cup to re-pump.
Use it for: Park your outdoor shower head on the steel side of the van between rinses, instead of on wet ground.
What it fits: Standard 3/4 inch shower head fitting, so most camper and RV heads drop straight in. 10 kg pull per magnet on steel body panels.
Shipping: Ships within 48 h. Free shipping from CHF150, £150, €250 or $279.
Put the shower head somewhere that holds it.
An outdoor shower needs a place to put the head down. The ground is wet, the hose pulls back, and your hands are busy. Three fixes exist. One without a catch.
Vacuum mount
A suction cup under a hose that pulls back. Weaker than a magnet, and it lets go when you need it least.
Drilled bracket
Decades-old generic hardware. Holes in the panel to fit it. Permanent.
Magnetic look-alike
A recent copy of our design, usually made in Asia. Pull force often unspecified.
Tactic magnet
10 kg pull per magnet, tested. On in seconds, off in seconds. No holes in your van.
Will it hold on your van?
The rule: the magnet needs steel underneath. Most van body panels are steel. Some are not.
Holds
Does not hold
What you get
Standard 3/4" fitting
The bracket matches the size of a home shower head, so most camper and RV heads drop straight in.
Two internal diameters
Most shower-head tubes are slightly conical. The mount matches that geometry and grips more securely.
No drilling, no adhesive
Adjustable and removable. The panel stays exactly as it left the factory.
Carbon fibre reinforced nylon
SLS 3D-printed at 270 °C in Switzerland. The same material we use across the magnetic range.
Dimensions
The mount is built around the shower head of the Hymer Grand Canyon S, which is the same diameter as a standard home shower head. Send us your shower head model and we will check the dimensions with you.
Specifications
3D-printed, not injection moulded. Minor visible layers or slight waviness come with the process. Anything with a noticeable defect is separated out and never shipped.
From the wild
Pair and save
- Shower Bundle (2-piece) — shower head holder and towel hook. The essentials for outdoor showering.
- Complete Shower Kit (3-piece) — shower head holder, shampoo holder and towel holder. The full outdoor bathroom.
Magnetic Towel Hook · Magnetic Shower Gel Holder · Modular Soap Holder for Hymer · Shower Curtain Holder
The original. Invented here.
Tactic Engineering invented the magnetic vehicle mount. Designed and prototyped in Switzerland, stress-tested on the road, first units shipped in December 2021. Every magnetic mount on the market today came after ours.
Sold worldwide through
Shipping, duties and warranty
Legal notice: under Swiss regulation, magnetic supports are classified as cargo securing equipment, for which the driver is responsible. Tactic Engineering cannot be held accountable for any incident resulting from the use of our products. It is the user's responsibility to comply with local regulations on cargo securing. Use the magnetic supports responsibly.
Hymer® is a trademark of Hymer GmbH & Co. KG. Tactic Engineering is an independent manufacturer and is not affiliated with, endorsed by, or sponsored by Hymer.
Compatibility at a glance
| Item | Works | Notes |
|---|---|---|
| Standard 3/4" shower heads | Yes | Matches the size of a home shower head. Two internal diameters, 21.52 mm and 22.43 mm, for conical tubes. |
| Hymer Grand Canyon S shower head | Yes | The mount was designed around it. |
| Steel body panels (most vans) | Yes | Flat, clean, bare-painted steel. |
| Aluminium panels or doors | No | No magnet holds on aluminium. |
| Curved or ribbed areas | Reduced hold | Any air gap costs hold force. |
| Thick wrap or dirt under the magnet | Reduced hold | Clean the panel first. |
Ten-second test: put a fridge magnet where the mount will sit. If you have to pull to get it off, this mount holds there. Not sure about your shower head? Send us its model and we will check the dimensions.
FAQ
Will my shower head fit?
Most camper and RV shower heads use the standard 3/4" size and drop straight in. The mount has two internal diameters, 21.52 mm and 22.43 mm, because most shower-head tubes are slightly conical.
How strong is the magnet?
10 kg of pull per magnet, tested.
Why not a suction cup?
A suction cup lets go when the hose pulls back, and needs re-pumping. The magnet holds on steel and comes off in seconds.
Do I need to drill?
No drilling, no adhesive. Adjustable and removable. The panel stays as it left the factory.
What is it made of?
Carbon fibre reinforced nylon, SLS 3D-printed at 270 °C in Switzerland.
What about shipping and warranty?
Orders ship within 48 working hours from our Swiss facility. EU VAT and duties are included. The warranty is 2 years worldwide, and every part is replaceable.
Related guide
Quick questions
Can I move it later?
Yes. It is magnetic, so you lift it off and place it somewhere else in seconds, with no tools and no marks.
Will it hold on my vehicle?
The magnet needs steel underneath. It holds on steel panels and not on aluminium. Not sure? If a fridge magnet sticks firmly to the spot, it will hold.
Pairs well with
swiss made
the original
Magnetic Shower Mount