Fiat Ducato 2022+ Phone Mount
Buy it with — Carry skis, boards, or kites. Magnetic, no roof rack needed.
Details that make the difference
Look at the black rubber strip.
There are many phone mounts out there. Nobody else uses it.
- Quiet. The rubber absorbs vibration, so the mount adds no rattle or noise while you drive.
- Stays put. The rubber is thicker than the slot, so the mount is hard to pull out, even without adhesive tape.
- No scratches. No plastic rubbing on plastic, so your interior stays as it left the factory.
Typical hobby 3D-printed mounts do not have it.
Ball joint
Knurled grip
Tilt the phone within its range to the angle you like.
The knurled nut gives more grip when you tighten it to lock the position.
Trusted by the industry
Fiat Ducato 2022+ Phone Mount
Vehicle-specific magnetic phone mount. Pick the head that fits the gear you already own.
Check your cup holder first.
This mount is made for the current-generation centre cup holder on the Ducato platform. Compare yours with the diagram for this mount, or the cup holder photo in the gallery, before ordering. If you have the older round cup holder with the step and a TX25 Torx screw at the bottom, you need the other version.
Same as the photoThis mount
Current-generation centre cup holder on Fiat Ducato 2022+ and sister vans. You are on the right page.
Older cup holderThe other version
Your van has the older round cup holder with the step and TX25 screw. Order the Fiat Ducato pre-2022 & Ram ProMaster Phone Mount. Not sure? Send us a photo of your cup holder and we will tell you which one fits.
At a glance
Use it for
Keep your phone in view in the Fiat Ducato, charging over Qi2 MagSafe up to 15 W, with a ball joint and knurled grip to set the angle.
What it fits
Fiat Ducato X290 (2022+), Peugeot Boxer (2022+), Citroën Relay / Jumper (2022+), Opel / Vauxhall Movano (2023+), Toyota ProAce Max (2024+), and campers on this platform that keep the original dashboard cupholder. RAM ProMaster or pre-2022 Ducato? See Fiat Ducato pre-2022 & Ram ProMaster Phone Mount.
Shipping
Leaves our Swiss workshop within 48 working hours. Free shipping from CHF 150, £150, €250 or $299.
One base. Two heads.
Same vehicle-specific base. Two heads so the mount works with the gear you already own.
MagSafe
A complete kit. Mount plus a MagSafe-compatible Qi2 wireless charger. Plug in USB-C, snap your phone on, drive.
Quad Lock®
A small plastic adapter we designed and manufacture in-house, fitting between our vehicle-specific base and your existing Quad Lock® MAG charger. You bring the Quad Lock® Wireless Charging Head and a Quad Lock® compatible case. Both sold separately by Quad Lock.
Adding a Quad Lock charger?
Fitting the Quad Lock® MAG wireless charging head to the Quad Lock variant takes five minutes. Watch the walkthrough.
Built for your van.
Made for your van
Slots into the factory cup holder or ashtray.
Designed in Switzerland
Engineered and manufactured in-house.
No drilling, no adhesive
Reversible install in 60 seconds.
2-year warranty
Spare parts always available.
Not sure which one? Find your fit.
| iPhone 12+ (no case or Apple MagSafe case) | MagSafe |
| Peak Design MagSafe case | MagSafe |
| Quad Lock MagSafe case (no Quad Lock charger yet) | MagSafe |
| Quad Lock MAG case + already own the charger | Quad Lock |
Fitment.
Fits any vehicle with the dashboard cupholder shown in the product images. Confirmed fitment:
- Fiat Ducato X290 (2022+).
- Peugeot Boxer (2022+).
- Citroën Relay / Jumper (2022+).
- Opel / Vauxhall Movano (2023+).
- Toyota ProAce Max (2024+).
These vehicles all share the Ducato dashboard platform. The mount also fits motorhome and camper conversions built on this platform (Pilote, Hymer, Rapido, Adria, Chausson, Carthago, etc.) as long as they retain the original dashboard cupholder.
Not compatible: RAM ProMaster (different cupholder geometry), and pre-2022 Ducato / Boxer / Jumper / Movano (earlier dashboard). If your cupholder doesn't match the photo, the mount won't fit. Check before ordering.
If yours is the round one with the step and a TX25 Torx screw, take the Fiat Ducato pre-2022 & Ram ProMaster Phone Mount.
Warranty.
Two-year warranty. Spare parts always available.
Specifications.
MagSafe® and iPhone® are trademarks of Apple Inc. Quad Lock® is a trademark of Annex Products Pty Ltd. Peak Design® is a trademark of Peak Design Ltd. RAM Mounts® and X-Grip® are trademarks of National Products Inc. Tactic Engineering is an independent manufacturer and is not affiliated with, endorsed by, or sponsored by any of the above companies.
Compatibility at a glance
| Vehicle or item | Fit |
|---|---|
| Fiat Ducato 2022+ | Yes |
| Any other vehicle | No |
FAQ
Which charger or head do I get?
Two options on the same base: the MagSafe kit with a MagSafe-compatible Qi2 wireless charger (up to 15 W over USB-C, iPhone 12 and newer), or a Quad Lock® adapter for your existing Quad Lock® MAG wireless charging head, sold separately by Quad Lock.
Can I adjust the angle of my phone?
Yes. The ball joint lets you tilt the phone within its range to the angle you like, and the knurled nut gives more grip when you tighten it to lock the position.
Will it rattle or scratch my console?
No. A black rubber strip absorbs vibration, holds the base firmly in place without adhesive tape and stops plastic rubbing on plastic, so your interior stays as it left the factory.
How fast does it ship, and is shipping free?
Orders leave our Swiss facility within 48 working hours. Shipping is free from CHF 150 in Switzerland and £150 in the UK, and from €250 in the EU and $299 in the US.
Quick questions
Which phones work with the MagSafe head?
iPhone 12 and newer, or any Android phone with a MagSafe-compatible case up to 3 mm.
Pairs well with
It starts as a 3D scan of your car.
Then hours and hours of modelling. Then nylon powder, fused by a laser one layer at a time, until the powder holds the shape of your console.
The rubber is the whole point.
This mount is designed with rubber around it. That rubber is what locks it in place — and what keeps it from ever marking the interior. Nothing scratches. Nothing presses into leather or Alcantara.
It is also why it goes in and comes out in seconds. No tape to peel off and no residue left behind. No suction cup to let go in the heat. No tools, no screws, nothing driven into dashboard plastics that were never made to take it.
We do the hours so the install takes seconds.
Scanning, modelling, printing, finishing and assembly happen in one building in Ticino, Switzerland. Nothing arrives finished. Nothing is rebadged. When a part needs to change, it changes that week.
swiss made
the original
