Fiat Ducato pre-2022 & Ram ProMaster Phone Mount
Trusted by the industry
Fiat Ducato pre-2022 & Ram ProMaster Phone Mount
One dashboard, four badges. Fiat Ducato, Citroën Jumper / Relay, Peugeot Boxer and Ram ProMaster. Sits in the centre cup holder. One TX25 Torx screw. No drilling. No adhesive.
Check your cup holder first.
This mount is made for one cup holder: the round one in the centre of the dashboard, with the step through the middle and a Torx screw at the bottom. Compare yours with the cup holder photo in the gallery before ordering.
This mount
Round cup holder, step in the middle, TX25 Torx screw at the bottom. You are on the right page.
The other version
Your van needs the Fiat Ducato 2022+ Phone Mount. Not sure? Send us a photo of your cup holder and we will tell you which one fits.
One screw. Done.
Remove the TX25 Torx screw at the bottom of the cup holder and fit the mount in its place. Plug the charger into a USB-C source. Snap the phone on, drive.
Nothing is cut, drilled or glued. Take the mount out and the cup holder is back to factory.
Four badges. One dashboard.
In this generation the Fiat Ducato, Citroën Jumper (Relay in the UK), Peugeot Boxer and Ram ProMaster 1500 / 2500 / 3500 leave the same factory with the same dashboard. Same centre cup holder, same TX25 screw, same mount.
Ram ProMaster owners: this is your ProMaster phone mount. It charges, holds the phone where you can see it, and leaves the dash untouched.
Opel / Vauxhall Movano owners: up to 2021 the Movano is built on the Renault Master, a different dashboard. From 2021 it is built on the Ducato. If your cup holder matches the photo, this mount fits. If not, take the 2022+ version.
Fitment. Read this before ordering.
Fits, with the cup holder shown in the photo
Does not fit
Fiat Ducato 2022+ Phone Mount. Also fits Citroën Jumper / Relay, Peugeot Boxer, Opel Movano and Toyota ProAce Max of the current generation.
Built for the van
Made for the cup holder
Shaped to the centre cup holder. Sits low, out of the way of the radio and the vents.
No drilling, no adhesive
One factory Torx screw. Reversible. Relevant at resale and on fleet vans.
Magnetic Qi2 alignment
The phone stays put on cobbles, gravel and speed bumps. You pull it off. It does not fall off.
Designed and made in Switzerland
Sintered nylon, manufactured in-house. 2-year warranty in Switzerland and the EU, 1 year elsewhere. Every part replaceable at fair prices.
Specifications
MagSafe® and iPhone® are trademarks of Apple Inc. Fiat®, Ducato®, Citroën®, Peugeot®, Opel®, Vauxhall®, Ram® and ProMaster® are trademarks of their respective owners. Tactic Engineering is an independent manufacturer and is not affiliated with, endorsed by, or sponsored by any of the above companies.
It starts as a 3D scan of your car.
Then hours and hours of modelling. Then nylon powder, fused by a laser one layer at a time, until the powder holds the shape of your console.
The rubber is the whole point.
This mount is designed with rubber around it. That rubber is what locks it in place — and what keeps it from ever marking the interior. Nothing scratches. Nothing presses into leather or Alcantara.
It is also why it goes in and comes out in seconds. No tape to peel off and no residue left behind. No suction cup to let go in the heat. No tools, no screws, nothing driven into dashboard plastics that were never made to take it.
We do the hours so the install takes seconds.
Scanning, modelling, printing, finishing and assembly happen in one building in Ticino, Switzerland. Nothing arrives finished. Nothing is rebadged. When a part needs to change, it changes that week.
swiss made
the original
Fiat Ducato pre-2022 & Ram ProMaster Phone Mount
LHD / MagSafe-compatible (charger included)