Buy it with — Carry skis, boards, or kites. Magnetic, no roof rack needed.
Porsche Taycan Phone Mount
Details that make the difference
Look at the black rubber strip.
There are many phone mounts out there. Nobody else uses it.
- Quiet. The rubber absorbs vibration, so the mount adds no rattle or noise while you drive.
- Stays put. The rubber is thicker than the slot, so the mount is hard to pull out, even without adhesive tape.
- No scratches. No plastic rubbing on plastic, so your interior stays as it left the factory.
Typical hobby 3D-printed mounts do not have it.
Ball joint
Knurled grip
Tilt the phone within its range to the angle you like.
The knurled nut gives more grip when you tighten it to lock the position.
Trusted by the industry
Porsche Taycan Phone Mount
The factory wireless charger sits under a lid. It traps heat, it will not take a modern iPhone flat, and you cannot see the screen while it charges. This is where the phone goes instead.
New: black version, on trial from 23 October until 22 November 2026. It costs CHF 5 more because each mount is painted by hand with an industrial chemical coating.
At a glance
Use it for
Keep your phone in view in the Taycan, charging over Qi2 MagSafe up to 15 W, with a ball joint and knurled grip to set the angle.
What it fits
Porsche Taycan / 4S / GTS / Turbo / Turbo S / Turbo GT, Sport Turismo, Cross Turismo (all years). Sits in the factory cupholder, no drilling, no adhesive. LHD and RHD.
Shipping
Leaves our Swiss workshop within 48 working hours. Free shipping from CHF 150, £150, €250 or $279.
Why this exists.
Porsche built a wireless charging pad into the centre console and put a lid over it. In practice Taycan owners stop using it within weeks. The lid traps heat, so the phone throttles on a warm day. The camera bump on an iPhone 14 and newer stops it lying flat against the pad. And with the lid closed you cannot see the screen, which is the one thing you wanted the phone for.
The alternatives are worse. A vent clip loads the air blades of a car whose interior was machined, not moulded. An adhesive pad leaves a mark on the dash that never comes out and shows up under sun. A suction cup on the windscreen is restricted in several European countries and gives up the first properly hot day.
So it goes in the cupholder. That is the one place in a Taycan where a mount can sit without touching a vent, a screen, the leather or the Alcantara. It pushes in, the rubber ring locks it, and it comes out in seconds leaving nothing behind.
One base. Two heads.
The base is shaped to the Taycan cupholder and pushes straight in. On top, pick the head that matches the gear you already own.
MagSafe
A complete kit. Mount plus a MagSafe-compatible Qi2 wireless charger, up to 15 W over USB-C. Snap the phone on, drive. iPhone 12 and newer, Apple MagSafe cases, Peak Design cases and Quad Lock cases, up to 3 mm thick.
Quad Lock®
A sintered-nylon adapter we design and manufacture in-house, fitting between our base and your existing Quad Lock® MAG wireless charging head. You bring the Quad Lock® head and case, both sold separately by Quad Lock.
iPhone 12+ bare or in an Apple MagSafe case — MagSafe. Peak Design MagSafe case — MagSafe. Quad Lock MagSafe case but no Quad Lock charger yet — MagSafe. Quad Lock MAG case and you already own the charging head — Quad Lock.
Five minutes. Watch the walkthrough on YouTube.
Fitment. Read this before ordering.
The rule: the cupholder geometry is identical across the whole Taycan range. One mount, every model, every variant, every model year since launch.
Fits
Every other model has a different console or a different cupholder, so each one has its own mount: 911 991 (2012–2019) · 911 992 (2020+) · 718 Cayman & Boxster (2017+) · Boxster & Cayman 981 (2013–2016) · Macan · Macan EV. Or browse the full range: vehicle-specific phone mounts.
Built for the car
Scanned, not guessed
Drawn from a precision 3D scan of the OEM Taycan cupholder at 0.1 mm. It sits where it belongs and nowhere else.
Push-fit. No tools.
The rubber ring creates a friction lock. No clips, no suction cups, no adhesive, no drilling. It does not scratch and it does not rattle.
Magnetic Qi2 alignment
The phone snaps on. Rotate it toward the driver and it stays where you put it.
Designed and made in Switzerland
Sintered nylon, manufactured in-house. 70 grams. Spare parts always available.
Specifications
Mount
MagSafe variant — Taycan base with Qi2 charger
Included Qi2 charger
Quad Lock® variant — adapter only
MagSafe® and iPhone® are trademarks of Apple Inc. Quad Lock® is a trademark of Annex Products Pty Ltd. Peak Design® is a trademark of Peak Design Ltd. Porsche® and Taycan® are trademarks of Dr. Ing. h.c. F. Porsche AG. Tactic Engineering is an independent manufacturer and is not affiliated with, endorsed by, or sponsored by any of the above companies.
Compatibility at a glance
| Vehicle or item | Fit |
|---|---|
| Taycan, 4S, GTS, Turbo, Turbo S, Turbo GT | Yes |
| Sport Turismo and Cross Turismo | Yes |
| Every model year since launch, LHD and RHD | Yes |
| Other Porsche models | No, each has its own mount |
FAQ
Does it fit my Taycan?
Yes. The cupholder is identical across the whole Taycan range, so one mount fits every variant, Sport Turismo and Cross Turismo, every model year, left- and right-hand drive. It pushes into the cupholder, no tools.
Which charger or head do I get?
Two options on the same base: the MagSafe kit with a MagSafe-compatible Qi2 wireless charger (up to 15 W over USB-C, iPhone 12 and newer), or a Quad Lock® adapter for your existing Quad Lock® MAG wireless charging head, sold separately by Quad Lock.
Can I adjust the angle of my phone?
Yes. The ball joint lets you tilt the phone within its range to the angle you like, and the knurled nut gives more grip when you tighten it to lock the position.
How fast does it ship, and is shipping free?
Orders leave our Swiss facility within 48 working hours. Shipping is free from CHF 150 in Switzerland and £150 in the UK, and from €250 in the EU and $279 in the US.
Related guide
Quick questions
Which phones work with the MagSafe head?
iPhone 12 and newer, or any Android phone with a MagSafe-compatible case up to 3 mm.
Pairs well with
It starts as a 3D scan of your car.
Then hours and hours of modelling. Then nylon powder, fused by a laser one layer at a time, until the powder holds the shape of your console.
The rubber is the whole point.
This mount is designed with rubber around it. That rubber is what locks it in place — and what keeps it from ever marking the interior. Nothing scratches. Nothing presses into leather or Alcantara.
It is also why it goes in and comes out in seconds. No tape to peel off and no residue left behind. No suction cup to let go in the heat. No tools, no screws, nothing driven into dashboard plastics that were never made to take it.
We do the hours so the install takes seconds.
Scanning, modelling, printing, finishing and assembly happen in one building in Ticino, Switzerland. Nothing arrives finished. Nothing is rebadged. When a part needs to change, it changes that week.
swiss made
the original
Looks good, fits very well in the cupholder.
The magsafe Taycan charger that sits in one of the cupholders seems to me to be the ideal location to charge and access a cellphone. Previously I had a similar product custom designed which work pretty well but was not a snug fit. That is not the case with Tactic's product: it fits great. One word of caution: although the attachment swivels, it doesn't swivels 360° meaning that one should never try to move the swivel in a direction where there is resistance. I also found the tech support at Tactic very responsive and helpful.
The magsafe for the Taycan fits perfectly. Great product. And the team is really helpful and responsive.
Mount has a perfect fit in my Taycan. Best solution for parking my iPhone!
Perfect fit, nice and fast charger!
Quick delivery to the U.K.
Porsche Taycan Phone Mount
Quad Lock adapter only – charger NOT included / Standard